59 Results for : comparator
-
LM 361 M - Komparator, 1-fach, SO-14
The LM161/LM361 is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics over the SE529/NE529 for which it is a pin-for-pin replacement. The device has been optimized for greater speed performance and lower input offset voltage. Typically delay varies only 3 ns for over-drive variations of 5 mV to 500 mV. It may be operated from op amp supplies (±15V).- Shop: reichelt elektronik
- Price: 4.37 EUR excl. shipping
-
LM 361 N - Komparator, 1-fach, DIP-14
The LM161/LM361 is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics over the SE529/NE529 for which it is a pin-for-pin replacement. The device has been optimized for greater speed performance and lower input offset voltage. Typically delay varies only 3 ns for over-drive variations of 5 mV to 500 mV. It may be operated from op amp supplies (±15V).- Shop: reichelt elektronik
- Price: 2.31 EUR excl. shipping
-
MCP 8024-H/MP - Motortreiber, für DC-Motoren, QFN-40
The MCP8024 is a 3-Phase Brushless DC (BLDC) Gate Driver with power module. The MCP8024 device integrates three half-bridge drivers to drive external NMOS/NMOS transistor pairs configured to drive a 3-phase BLDC motor, a comparator, a voltage regulator to provide bias to a companion microcontroller, power monitoring comparators, an overtemperature sensor, two level translators and three operational amplifiers for motor current monitoring.• Three Half-bridge Drivers Configured to Drive External High-Side NMOS and Low-Side NMOS MOSFETs• Independent input control for high-side NMOS and low-side NMOS MOSFETs• Peak output current: 0.5A @ 12V• Shoot-through protection• Overcurrent and short circuit protection • Adjustable Output Buck Regulator (750 mW)• Fixed Output Linear Regulators: 5V @ 20 mA12V @ 20 mA• Internal Bandgap Reference• Three Operational Amplifiers for Motor Phase Current Monitoring and Position Detection• Overcurrent Comparator• Two Level Translators• Input Voltage Range: 6 - 40V • Operational Voltage Range: 6 - 28V• Undervoltage Lockout (UVLO): 6V• Overvoltage Lockout (OVLO): 28V• Transient (100 ms) Voltage Tolerance: 48V• Extended Temperature Range: TA -40 to +150°C• Thermal Shutdown- Shop: reichelt elektronik
- Price: 3.21 EUR excl. shipping
-
TLV 3502 AID - 4.5ns Rail-to-Rail, High-Speed Comparator, SO-8
The TLV350x family of push-pull output comparators feature a fast 4.5ns propagation delay and operation from +2.7V to +5.5V. Beyond-the-rails input common-mode range makes it an ideal choice for low-voltage applications. The rail-to-rail output directly drives either CMOS or TTL logic.- Shop: reichelt elektronik
- Price: 9.00 EUR excl. shipping
-
DS 1818 R-10 - Spannungsdetektor, 2.88V, SOT-23
The DS1818 EconoReset uses a precision temperature-compensated reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 150 ms to allow the power supply and processor to stabilize.- Shop: reichelt elektronik
- Price: 2.10 EUR excl. shipping
-
ARD SENS MIK-S - Arduino - Mikrofon Schallsensor
Sehr empfindliches Modul mit 2 Ausgängen.AO - Analogeingang, Echtzeit-Ausgangsspannungssignal des Mikrofons.DO - der digitale Ausgang hängt von der Lautstärke und der eingestellten Grenze ab.Spezifikationen• Spannung: 3.3 bis 5 VDC• Ausgänge: 1x analog + 1x digital• Befestigung: 1 Montageloch (3 mm)• 2 LEDs: 1x Stromversorgungs-LED + 1x Comparator Ausgangs-LED• Frequenzbereich: 50 Hz .. 20 KHz• Impedanz: 2,2 KOhm• Empfindlichkeit: 48 - 66 dB• Betriebstemperatur: -40 .. +85 °C• Maße (L x B x H): 44 x 15 x 10 mm- Shop: reichelt elektronik
- Price: 6.10 EUR excl. shipping
-
MC 33063 AP1G - Step-Up/Down, adj., 3 ... 40 V, 40 V, DIL-8
The MC34063A Series is a monolithic control circuit containing the primary functions required for DC-to-DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically designed to be incorporated in Step-Down and Step-Up and Voltage-Inverting applications with a minimum number of external components. Refer to Application Notes AN920A/D and AN954/D for additional design information.- Shop: reichelt elektronik
- Price: 0.90 EUR excl. shipping
-
TL 331 IDBVR - Komparator, 1-fach, SOT-23-5
This device consists of a single voltage comparator that is designed to operate from a single power supply over a wide range of voltages. Operation from dual supplies also is possible if the difference between the two supplies is 2 V to 36 V and V CC is at least 1.5 V more positive than the input common-mode voltage. Current drain is independent of the supply voltage. The output can be connected to other open-collector outputs to achieve wired-AND relationships.- Shop: reichelt elektronik
- Price: 0.55 EUR excl. shipping
-
The Current Comparator
The Current Comparator ab 125.99 € als gebundene Ausgabe: . Aus dem Bereich: Bücher, Wissenschaft, Technik,- Shop: hugendubel
- Price: 125.99 EUR excl. shipping
-
DS 1232 LP - Überwachungs-IC, Resetschaltung, DIP-8
The DS1232LP/LPS Low Power MicroMonitor Chip monitors three vital conditions for a microprocessor: power supply, software execution, and external over-ride. First, a precision temperature-compensated reference and comparator circuit monitors the status of VCC. When an out-of-tolerance condition occurs, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signals are kept in the active state for a minimum of 250 ms to allow the power supply and processor to stabilize.- Shop: reichelt elektronik
- Price: 4.27 EUR excl. shipping